CC1021-RTR1 datasheet(60/92 Pages) TI

60 / 92 page

CC1021

SWRS045

Page 60 of 91

21.

Interrupt on Pin DCLK

21.1. Interrupt upon PLL Lock

In synchronous mode the DCLK pin on

CC1021 can be used to give an interrupt

signal to wake the microcontroller when

the PLL is locked.

PD_MODE[1:0] in the MAIN register

should be set to 01. If DCLK_LOCK in the

INTERFACE register is set to 1 the DCLK

signal is always logic high if the PLL is not

in lock. When the PLL locks to the desired

frequency the DCLK signal changes to

logic 0. When this interrupt has been

detected write PD_MODE[1:0] = 00. This

will enable the DCLK signal.

This function can be used to wait for the

PLL to be locked before the PA is ramped

up in transmit mode. In receive mode, it

can be used to wait until the PLL is locked

before searching for preamble.

21.2. Interrupt upon Received Signal Carrier Sense

In synchronous mode the DCLK pin on

CC1021 can also be used to give an

interrupt signal to the microcontroller when

the RSSI level exceeds a certain threshold

(carrier sense threshold). This function can

be used to wake or interrupt the

microcontroller when a strong signal is

received.

Gating the DCLK signal with the carrier

sense signal makes the interrupt signal.

This function should only be used in

receive mode and is enabled by setting

DCLK_CS = 1 in the INTERFACE register.

The DCLK signal is always logic high

unless carrier sense is indicated. When

carrier sense is indicated the DCLK starts

running. When gating the DCLK signal

with the carrier sense signal at least 2

dummy bits should be added after the data

payload in TX mode. The reason being

that the carrier sense signal is generated

earlier in the receive chain (i.e. before the

demodulator), causing it to be updated 2

bits before the corresponding data is

available on the DIO pin.

In transmit mode DCLK_CS must be set to

0. Refer to CC1021 Errata Note 001.

22.

PA_EN and LNA_EN Digital Output Pins

22.1. Interfacing an External LNA or PA

CC1021 has two digital output pins, PA_EN

and LNA_EN, which can be used to

control an external LNA or PA. The

functionality of these pins are controlled

through the INTERFACE register. The

outputs can also be used as general digital

output control signals.

EXT_PA_POL and EXT_LNA_POL control

the active polarity of the signals.

EXT_PA and EXT_LNA control the

function of the pins. If EXT_PA = 1, then

the PA_EN pin will be activated when the

internal PA is turned on. Otherwise, the

EXT_PA_POL bit controls the PA_EN pin

directly. If EXT_LNA = 1, then the

LNA_EN pin will be activated when the

internal LNA is turned on. Otherwise, the

EXT_LNA_POL bit controls the LNA_EN

pin directly.

These two pins can therefore also be used

as two general control signals, section

21.2. In the Chipcon reference design

CC1021-RTR1 Datasheet(PDF) 60 Page - Texas Instruments

CC1021-RTR1 Datasheet(HTML) 60 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

Datasheet Descarga

Enlace URL