ST10F272M datasheet(84/175 Pages) STMICROELECTRONICS

84 / 175 page

System reset

ST10F272M

84/176

after a reset sequence.

Short and long synchronous reset

Once the first maximum 16 TCL are elapsed (4+12TCL), the internal reset sequence starts.

It is 1024 TCL cycles long: at the end of it, and after other 8TCL the level of RSTIN is

sampled (after the filter, see RSTF in the drawings): if it is already at high level, only Short

Reset is flagged (refer to Chapter 19 for details on reset flags); if it is recognized still low, the

Long reset is flagged as well. The major difference between Long and Short reset is that

during the Long reset, also P0(15:13) become transparent, so it is possible to change the

clock options.

Warning:

In case of a short pulse on RSTIN pin, and when Bidirectional

reset is enabled, the RSTIN pin is held low by the internal

circuitry. At the end of the 1024 TCL cycles, the RTSIN pin is

released, but due to the presence of the input analog filter the

internal input reset signal (RSTF in the drawings) is released

later (from 50 to 500ns). This delay is in parallel with the

additional 8 TCL, at the end of which the internal input reset

line (RSTF) is sampled, to decide if the reset event is Short or

Long. In particular:

●

If 8 TCL > 500ns (fCPU < 8 MHz), the reset event is always recognized as Short

●

If 8 TCL < 500ns (fCPU > 8 MHz), the reset event could be recognized either as Short or

Long, depending on the real filter delay (between 50 and 500ns) and the CPU

frequency (RSTF sampled High means Short reset, RSTF sampled Low means Long

reset). Note that in case a Long Reset is recognized, once the 8 TCL are elapsed, the

P0(15:13) pins becomes transparent, so the system clock can be reconfigured. The

port returns not transparent 3-4TCL after the internal RSTF signal becomes high.

The same behavior just described, occurs also when unidirectional reset is selected and

RSTIN pin is held low till the end of the internal sequence (exactly 1024TCL + max 16 TCL)

and released exactly at that time.

Note:

When running with CPU frequency lower than 40 MHz, the minimum valid reset pulse to be

recognized by the CPU (4 TCL) could be longer than the minimum analog filter delay (50ns);

so it might happen that a short reset pulse is not filtered by the analog input filter, but on the

other hand it is not long enough to trigger a CPU reset (shorter than 4 TCL): this would

generate a Flash reset but not a system reset. In this condition, the Flash answers always

with FFFFh, which leads to an illegal opcode and consequently a trap event is generated.

Exit from synchronous reset state

The reset sequence is extended until the RSTIN level becomes high. Moreover, it is

internally prolonged by the Flash initialization when EA = 1 (internal memory selected).

Then, the code execution restarts. The system configuration is latched from Port0, and ALE,

RD and WR/WRL pins are driven to their inactive level. The ST10F272M starts program

execution from memory location 00'0000h in code segment 0. This starting location will

typically point to the general initialization routine. Timing of synchronous reset sequence are

summarized in Figures 21 and 22 where a Short Reset event is shown, with particular

emphasis on the fact that it can degenerate into Long Reset: the two figures show the

ST10F272M Datasheet(PDF) 84 Page - STMicroelectronics

ST10F272M Datasheet(HTML) 84 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL