ST10F272M datasheet(22/175 Pages) STMICROELECTRONICS

22 / 175 page

Memory organization

ST10F272M

22/176

After reset, the XRAM2 address range is 09’0000h - 09’3FFFh and is mirrored every

16 Kbyte boundary until 0F’FFFFh.

XRAM2 also represents the Stand-by RAM, which can be maintained biased through

EA /VSTBY pin when main supply VDD is turned off.

As the XRAM appears like external memory, it cannot be used as system stack or as

addressable.

SFR/ESFR: 1024 bytes (2 x 512 bytes) of address space is reserved for the special function

function of the different on-chip units.

CAN1: Address range 00’EF00h - 00’EFFFh is reserved for the CAN1 Module access. The

CAN1 is enabled by setting XPEN bit 2 of the SYSCON register and by setting CAN1EN bit

0 of the XPERCON register. Accesses to the CAN Module use demultiplexed addresses

and a 16-bit data bus (only word accesses are possible). Two wait states give an access

time of 100ns at 40 MHz CPU clock. No tri-state wait states are used.

CAN2: Address range 00’EE00h - 00’EEFFh is reserved for the CAN2 Module access. The

CAN2 is enabled by setting XPEN bit 2 of the SYSCON register and by setting CAN2EN bit

1 of the new XPERCON register. Accesses to the CAN Module use demultiplexed

addresses and a 16-bit data bus (only word accesses are possible). Two wait states give an

access time of 100ns at 40 MHz CPU clock. No tri-state wait states are used.

Note:

If one or the two CAN modules are used, Port 4 cannot be programmed to output all eight

segment address lines. Thus, only four segment address lines can be used, reducing the

external memory space to 5 Mbytes (1 Mbyte per CS line).

RTC: Address range 00’ED00h - 00’EDFFh is reserved for the RTC Module access. The

RTC is enabled by setting XPEN bit 2 of the SYSCON register and bit 4 of the XPERCON

(only word accesses are possible). Two waitstates give an access time of 100ns at 40 MHz

CPU clock. No tristate waitstate is used.

PWM1: Address range 00’EC00h - 00’ECFFh is reserved for the PWM1 Module access.

The PWM1 is enabled by setting XPEN bit 2 of the SYSCON register and bit 6 of the

XPERCON register. Accesses to the PWM1 Module use demultiplexed addresses and a 16-

bit data bus (only word accesses are possible). Two waitstates give an access time of 100ns

at 40 MHz CPU clock. No tristate waitstate is used. Only word access is possible.

ASC1: Address range 00’E900h - 00’E9FFh is reserved for the ASC1 Module access. The

ASC1 is enabled by setting XPEN bit 2 of the SYSCON register and bit 7 of the XPERCON

(only word accesses are possible). Two waitstates give an access time of 100ns at 40 MHz

CPU clock. No tristate waitstate is used.

SSC1: Address range 00’E800h - 00’E8FFh is reserved for the SSC1 Module access. The

SSC1 is enabled by setting XPEN bit 2 of the SYSCON register and bit 8 of the XPERCON

(only word accesses are possible). Two waitstates give an access time of 100ns at 40 MHz

CPU clock. No tristate waitstate is used.

I2C: Address range 00’EA00h - 00’EAFFh is reserved for the I2C Module access. The I2C is

enabled by setting XPEN bit 2 of the SYSCON register and bit 9 of the XPERCON register.

Accesses to the I2C Module use demultiplexed addresses and a 16-bit data bus (only word

ST10F272M Datasheet(PDF) 22 Page - STMicroelectronics

ST10F272M Datasheet(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL