AD9396SLASHPCB datasheet(12/48 Pages) AD

12 / 48 page

AD9396

Rev. 0 | Page 12 of 48

This introduces a 700 mV dc offset to the signal, which must be

removed for proper capture by the AD9396.

The key to clamping is to identify a portion (time) of the signal

when the graphic system is known to be producing black. An

offset is then introduced which results in the ADCs producing a

black output (Code 0x00) when the known black input is

present. The offset then remains in place when other signal

levels are processed, and the entire signal is shifted to eliminate

offset errors.

In most PC graphics systems, black is transmitted between

active video lines. With CRT displays, when the electron beam

has completed writing a horizontal line on the screen (at the

right side), the beam is deflected quickly to the left side of the

screen (called horizontal retrace) and a black signal is provided

to prevent the beam from disturbing the image.

In systems with embedded sync, a blacker-than-black signal

(HSYNC) is produced briefly to signal the CRT that it is time to

begin a retrace. For obvious reasons, it is important to avoid

clamping on the tip of HSYNC. Fortunately, there is virtually

always a period following HSYNC, called the back porch, where

a good black reference is provided. This is the time when

clamping should be done.

Clamp timing employs the AD9396 internal clamp timing

generator. The clamp placement register is programmed with

the number of pixel periods that should pass after the trailing

edge of HSYNC before clamping starts. A second register

(clamp duration) sets the duration of the clamp. These are both

8-bit values, providing considerable flexibility in clamp

generation. The clamp timing is referenced to the trailing edge

of HSYNC because, though HSYNC duration can vary widely,

the back porch (black reference) always follows HSYNC. A

good starting point for establishing clamping is to set the clamp

placement to 0x08 (providing 8 pixel periods for the graphics

signal to stabilize after sync) and set the clamp duration to 0x14

(giving the clamp 20 pixel periods to re-establish the black

reference). For three-level syncs embedded on the green

channel, it is necessary to increase the clamp placement to

beyond the positive portion of the sync. For example, a good

clamp placement (Register 0x19) for a 720p input is 0x26. This

delays the start of clamp by 38 pixel clock cycles after the rising

edge of the three-level sync, allowing plenty of time for the

signal to return to a black reference.

Clamping is accomplished by placing an appropriate charge on

the external input coupling capacitor. The value of this capa-

citor affects the performance of the clamp. If it is too small,

there is a significant amplitude change during a horizontal line

time (between clamping intervals). If the capacitor is too large,

then it takes excessively long for the clamp to recover from a

large change in the incoming signal offset. The recommended

value (47 nF) results in recovering from a step error of 100 mV

to within ½ LSB in 10 lines with a clamp duration of 20 pixel

periods on a 75 Hz SXGA signal.

YUV Clamping

YUV graphic signals are slightly different from RGB signals in

that the dc reference level (black level in RGB signals) can be

at the midpoint of the graphics signal rather than the bottom.

For these signals it can be necessary to clamp to the midscale

range of the ADC range (128) rather than the bottom of the

ADC range (0).

Clamping to midscale rather than ground can be accomplished

by setting the clamp select bits in the serial bus register. Each of

the three converters has its own selection bit so that they can be

clamped to either midscale or ground independently. These bits

are located in Register 0x1B [7:5]. The midscale reference

voltage is internally generated for each converter.

Auto-Offset

The auto-offset circuit works by calculating the required offset

setting to yield a given output code during clamp. When this

block is enabled, the offset setting in the I2C is seen as a desired

clamp code rather than an actual offset. The circuit compares

the output code during clamp to the desired code and adjusts

the offset up or down to compensate.

The offset on the AD9396 can be adjusted automatically to a

specified target code. This option allows the user to set the

offset to any value and be assured that all channels with the

same value programmed into the target code will match. This

eliminates any need to adjust the offset at the factory. This

function is capable of running continuously any time the clamp

is asserted.

There is an offset adjust register for each channel, namely the

offset registers at the 0x08, 0x0A, and 0x0C addresses. The

offset adjustment is a signed (twos complement) number with

±64 LSB range. The offset adjustment is added to whatever

offset the auto-offset comes up with. For example: using ground

clamp, the target code is set to 4. To get this code, the auto-

offset generates an offset of 68. If the offset adjustment is set to

+10, the offset sent to the converter is 78. Likewise, if the offset

adjust is set to −10, the offset sent to the converter is 58. Refer

to application note AN-775, Implementing the Auto-Offset

Function of the AD9880, for a detailed description of how to use

this function.

Sync-on-Green (SOG)

The SOG input operates in two steps. First, it sets a baseline

clamp level from the incoming video signal with a negative peak

detector. Second, it sets the sync trigger level to a program-

mable level (typically 150 mV) above the negative peak. The

SOG input must be ac-coupled to the green analog input

through its own capacitor. The value of the capacitor must be

1 nF ± 20%. If SOG is not used, this connection is not required.

AD9396/PCB Datasheet(PDF) 12 Page - Analog Devices

AD9396/PCB Datasheet(HTML) 12 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

Datasheet Descarga

Enlace URL