MPC8377ECVRAFDA datasheet(47/124 Pages) FREESCALE

47 / 124 page

MPC8377E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 2

Freescale Semiconductor

Enhanced Secure Digital Host Controller (eSDHC)

This means that Data + Clock delay must be greater than –2 ns. This is always fulfilled.

11.3

eSDHC AC Timing Specifications (High-Speed Mode)

Table 42 provides the eSDHC AC timing specifications for high-speed mode as defined in Figure 30 and

Figure 31.

Table 42. eSDHC AC Timing Specifications for High-Speed Mode

At recommended operating conditions OVDD = 3.3 V ± 165 mV.

Parameter

Symbol1

Min

Max

Unit

Notes

SD_CLK clock frequency—high speed mode

fSHSCK

050

MHz

—

SD_CLK clock cycle

tSFSCK

—

SD_CLK clock frequency—identification mode

fSIDCK

0400

KHz

—

SD_CLK clock low time

tSHSCKL

7—

SD_CLK clock high time

tSHSCKH

7—

SD_CLK clock rise and fall times

tSHSCKR/

tSHSCKF

—3

Input setup times: SD_CMD, SD_DATx, SD_CD to

SD_CLK

tSHSIVKH

5—

Input hold times: SD_CMD, SD_DATx, SD_CD to SD_CLK

tSHSIXKH

0—

Output delay time: SD_CLK to SD_CMD, SD_DATx valid

tSHSKHOV

—4

Output Hold time: SD_CLK to SD_CMD, SD_DATx invalid

tSHSKHOX

0—

SD_CLK delay within device

tINT_CLK_DLY

1.5

—

SD Card Input Setup

tISU

6—

SD Card Input Hold

tIH

2—

SD Card Output Valid

tODLY

—14

SD Card Output Hold

tOH

2.5

—

Note:

1 The symbols used for timing specifications herein follow the pattern of t

(first three letters of functional block)(signal)(state)

(reference)(state) for inputs and t(first three letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tSFSIXKH

symbolizes eSDHC full mode speed device timing (SFS) input (I) to go invalid (X) with respect to the clock reference (K) going

to high (H). Also tSFSKHOV symbolizes eSDHC full speed timing (SFS) for the clock reference (K) to go high (H), with respect

to the output (O) going valid (V) or data output valid time. Note that, in general, the clock reference symbol representation is

based on five letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with

the appropriate letter: R (rise) or F (fall).

2 Measured at capacitive load of 40 pF.

3 For reference only, according to the SD card specifications.

4 Average, for reference only.

MPC8377ECVRAFDA Datasheet(PDF) 47 Page - Freescale Semiconductor, Inc

MPC8377ECVRAFDA Datasheet(HTML) 47 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL