ADT7463ARQZ-R7 datasheet(9/52 Pages) ONSEMI

9 / 52 page

REV. C

ADT7463

–9–

SERIAL BUS INTERFACE

Control of the ADT7463 is carried out using the serial system

management bus (SMBus). The ADT7463 is connected to this

bus as a slave device, under the control of a master controller.

The ADT7463 has a 7-bit serial bus address. When the device

is powered up with Pin 13 (PWM3/ADDRESS ENABLE) high,

the ADT7463 has a default SMBus address of 0101110 or

0x2E. The read/write bit must be added to get the 8-bit address. If

more than one ADT7463 is used in a system, then each ADT7463

should be placed in address select mode by strapping Pin 13 low on

power-up. The logic state of Pin 14 then determines the device’s

SMBus address. The logic of these pins is sampled upon power-up.

The device address is sampled and latched on the first valid

SMBus transaction, more precisely on the low-to-high transition

at the beginning of the 8th SCL pulse, when the serial bus address

byte matches the selected slave address. The selected slave address

is chosen using the address enable/address select pins. Any

attempted changes in the address will have no effect after this.

Table I. Address Select Mode

Pin 13 State

Pin 14 State

Address

0Low (10 k

Ω to GND)

0101100 (0x2C)

0High (10 k

Ω Pull-Up)

0101101 (0x2D)

1Don’t Care

0101110 (0x2E)

(Default)

ADT7463

ADDR_SEL

PWM3/ADDR_EN

VCC

10k�

ADDRESS = 0x2E

Figure 3. Default SMBus Address = 0x2E

ADT7463

ADDR_SEL

PWM3/ADDR_EN

10k�

ADDRESS = 0x2C

Figure 4. SMBus Address = 0x2C (Pin 14 = 0)

The ability to make hardwired changes to the SMBus slave

address allows the user to avoid conflicts with other devices sharing

the same serial bus, for example, if more than one ADT7463 is

used in a system.

The serial bus protocol operates as follows:

1. The master initiates data transfer by establishing a START

condition, defined as a high-to-low transition on the serial

data line SDA while the serial clock line SCL remains high.

This indicates that an address/data stream will follow. All

slave peripherals connected to the serial bus respond to the

START condition and shift in the next eight bits, consisting

of a 7-bit address (MSB first) plus a R/W bit, which deter-

mines the direction of the data transfer, i.e., whether data

will be written to or read from the slave device.

ADT7463

ADDR_SEL

PWM3/ADDR_EN

ADDRESS = 0x2D

VCC

10k�

Figure 5. SMBus Address = 0x2D (Pin 14 = 1)

ADT7463

ADDR_SEL

PWM3/ADDR_EN

VCC

10k�

DO NOT LEAVE ADDR_EN

UNCONNECTED! CAN

CAUSE UNPREDICTABLE

ADDRESSES.

CARE SHOULD BE TAKEN TO ENSURE THAT PIN 13

(PWM3/ADDR_EN) IS EITHER TIED HIGH OR LOW. LEAVING PIN 13

FLOATING COULD CAUSE THE ADT7463 TO POWER UP WITH AN

UNEXPECTED ADDRESS.

NOTE THAT IF THE ADT7463 IS PLACED INTO ADDRESS SELECT

MODE, PINS 13 AND 14 CANNOT BE USED AS THE ALTERNATE

FUNCTIONS (PWM3, TACH4/THERM) ONLY IF THE CORRECT

CIRCUIT IS MUXED IN AT THE CORRECT TIME.

Figure 6. Unpredictable SMBus Address if Pin 13

Is Unconnected

The peripheral whose address corresponds to the transmitted

address responds by pulling the data line low during the low

period before the ninth clock pulse, known as the Acknowl-

edge Bit. All other devices on the bus now remain idle while

the selected device waits for data to be read from or written

to it. If the R/W bit is a 0, then the master writes to the

slave device. If the R/W bit is a 1, the master reads from

the slave device.

Rev. 4 | Page 9 of 52 | www.onsemi.com

ADT7463ARQZ-R7 Datasheet(PDF) 9 Page - ON Semiconductor

ADT7463ARQZ-R7 Datasheet(HTML) 9 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

Datasheet Descarga

Enlace URL