AS3525 datasheet(30/194 Pages) AMSCO

30 / 194 page

AS3525-A/-B C22O22

Data Sheet, Confidential

www.austriamicrosystems.com

Revision 1.13

- 194

7.2.6 IDE Interface

Note: The IDE interface is only available on AS3525-A, not for AS3525-B because some of the IDE PINs are not bonded

within the AS3525-B package variant.

The IDE host interface core provides an efficient and easy-to-use interface to IDE and ATAPI devices. The core

implements programmable I/O, Multi-word DMA, and Ultra ATA-33, -66, -100 and -133 modes of operation and supports

up to two devices. The core interface to the system-on-chip provides PIO access and DMA capability to optimise data

transfers to and from the IDE devices. For ease of integration, this interface includes a register set compatible with the

Intel chip set, including a descriptor-based scatter-gather DMA core. This core is compatible with ATA-4 with Ultra ATA-

33, -66, -100 and -133 extensions. Single-word DMA is not supported.

The licensed SpeedSelect

TM technology allows the core to be reconfigured to support any timing mode for PIO, Multi-

Word DMA, and Ultra ATA transfers (-33, -66, -100 or -133) while running at any clock frequency. Interface to the host

processor is the AMBA AHB bus architecture.

There are two AHB interfaces on the core: an AHB master and an AHB slave.

7.2.6.1

AHB Master Interface

The AHB Master implements a subset of the AHB protocol. The following features are supported:

•

Single transfer, unspecified-length, 4-beat incrementing and optionally 8-beat incrementing bursts (HBURST will be

‘000’, ‘001’, ‘011’, or optionally ‘101’)

•

Accesses that cross a 1kB boundary will be unspecified-length incrementing (HBURST will be ‘001’)

•

16-bit and 32-bit transfers only (HSIZE will only be ‘001’ or ‘010’)

•

BUSY cycles are not issued (HTRANS will not be ‘01’)

•

HPROT is not implemented

•

OKAY, SPLIT and RETRY responses accepted (HRESP may be ‘00’, ‘10’ or ’11’)

•

HLOCK asserted during fixed-length bursts

•

The AHB master may be granted by default

7.2.6.2

AHB Slave Interface

The AHB Slave implements a subset of the AHB protocol. The following features are supported:

•

Non-burst only (HBURST must be ‘000’)

•

8-, 16-, or 32-bit transfers only (HSIZE must be ‘000’, ‘001’ or ‘010’)

•

No advantage is gained by issuing a SEQ cycle over a NONSEQ cycle (HTRANS values of ‘10’ and ‘11’ are

interpreted identically)

•

HPROT is ignored

•

HRESP is ‘00’ (OKAY)

•

HREADY is issued no sooner than 2 clock cycles after a valid SEQ or NONSEQ cycle

•

The AHB slave may be selected by default

AS3525 Datasheet(PDF) 30 Page - ams AG

AS3525 Datasheet(HTML) 30 Page - ams AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL