| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
DP83826AE Datasheet(PDF) 30 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
DP83826AE Datasheet(HTML) 30 Page - Texas Instruments |
|
30 / 113 page ![]() on-LAN interrupt flag configuration and status is located in the MII Interrupt Status Register #2 (MISR2, address 0x0013). 8.3.6 Low Power Modes The DP83826Ax device supports three low power modes. This section discusses the principles behind these low power modes and configuration to enable them. 8.3.6.1 Active Sleep Active sleep mode reduces power consumption when no link partner is connected. The feature can be enabled during initialization of the PHY by writing the correct bit to the PHYSCR register. The feature can be verified by reading the BISCR register. Once Active Sleep in enabled and when the PHY does not detect a cable connection, the PHY automatically enters active sleep mode. When the device enters this mode, all internal circuitry shuts down except for the SMI circuitry and energy detection circuitry on the TD± and RD± pins. In active sleep mode, the device transmits normal link pulses (NLP) every 1.4 seconds to check for the presence of a link partner. When a link partner is detected, the PHY automatically switches back to Normal mode, powering the rest of the internal circuitry. The device enables active sleep mode by setting bits[14:12] = 0b110 in the PHY Specific Control Register (PHYSCR, address 0x0011). 8.3.6.2 IEEE Power-Down IEEE power-down switch disables all PHY circuitry except the SMI and internal clock circuitry. IEEE power-down switch can be activated by either register access or through the INTR/PWRDN pin when the pin is configured for power-down function. To enable IEEE power-down switch through the INTR/PWRDN pin, the pin must be driven LOW to ground. To enable IEEE power-down switch through the SMI, set bit[11] = 1 in the BASIC mode Control Register (BMCR, address 0x0000). 8.3.6.3 Deep Power Down State A Deep Power Down state (DPD) disables all PHY circuitry except the SMI. In this mode, the device disables the PHY PLL to further reduce power consumption. The device uses this sequence to enter DPD state. 1. Enable DPD state (0x0428.2 = 1) 2. Enable IEEE power-down state (pin or 0x0000.11 = 1) 8.3.7 RMII Repeater Mode The DP83826Ax device provides the option to enable RMII back-to-back repeater mode functionality to extend cable reach. Two DP83826Ax devices can be connected in RMII repeater mode without need of any external configuration. The DP83826Ax provides a hardware strap to configure the CRS_DV pin of RMII interface to RX_DV pin for back-to-back operation. Figure 8-2 and Figure 8-3 show the RMII pin connections that enables the device to operate in repeater mode. DP83826AE, DP83826AI SNLS783 – MAY 2025 www.ti.com 30 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated Product Folder Links: DP83826AE DP83826AI |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |